Monday, March 7, 2016

Foam Board Bricks Using Weathering Powders



This morning I decided to experiment with some brick painting techniques. Since I did not have bricks, I had to first create a quick brick wall segment to work on. I suspect that lots of folks have problems building terrain out of foam board, so what follows is a quick tutorial on creating the little wall segment I made above. I did this quick and dirty, with little attention to detail. If you want a better result, definitely spend more time carefully sculpting the bricks. For me though, this was just enough to let me experiment with powders. 

There are two ways I know of getting the effect of mortar on bricks. The first is using enamels. I am partial to that method already, because cleanup and blending is quite easy using thinner. I already use enamels on most of my models, so it is not much of a step to use them on buildings. 

The second approach is to use pigments to simulate mortar. This has the advantage that the grainy texture of the pigments add a lot to the realism. The down side is that pigments are very messy and do not wear well for gaming miniatures. Irrespective of this fact, I think I prefer the pigment method. There is a nice tactile quality to the process, and the results are nearly instantaneous. The above wall segment took about an hour in total. The next step would have been to add dirt, streaking effects, and perhaps some mossy areas. Due to  purity seal foggy on me, I don't get to experiment further. That wall segment is currently a fuzzy white color. Damn you purity seal! (It bears mentioning again, never, ever, ever, EVER, use lacquer from a spray can. By brush or by airbrush are models protected)



When sculpting with foam board it is necessary to peal off one of the paper sides in order to expose the foam.


To sculpt the bricks I used an exact knife and tooth pick. A press mold is a better way to accomplish this. I normally take an old paint brush and pull out the bristles. The metal tip can then be bent into a nice rectangle shape and used as a mold.



To get a nice smooth finish I put on a little modeling paste. My paste had dried out so it was not ideal. Again, take time doing this.


A quick sanding of the bricks and plasterwork provides a relatively nice surface to paint.


I used three colors of paint for the bricks. The goal was to provide a nice top coat on the plaster. You can see how my sloppy brick work really shows through!



The fun step involves loading up the model with Secret Weapon Miniatures white weathering powder. I haven't had a use for this color before.


After working the powder in with a brush I licked my finger and used it to rub away the powder on the bricks. The weathering powder tastes terrible by the way.






7 comments:

  1. This guy http://thestonecuttersguild.tumblr.com/ does a ton of brick & stone carving into foam: his process is to 1) draw the bricks on the foam with a pen & ruler, 2) slice along the lines with a razor blade, 3) push into and long the cuts with a dull lead pencil, 4) rough up foam to taste by pressing into concrete, against balled up aluminum foil, etc.

    Might be speedier than punching in individual bricks

    ReplyDelete
    Replies
    1. That was a really interesting link. I appreciate the head up about it. I actually used a pencil to draw the bricks initially and then used an x-acto knife to cut the vertical separations in. The toothpick was used to sort of round the edges after the basic design was in. I think the best way is to fabricate a press tool.

      If I were going to make every house a custom build I would need to find a faster way to do it, but since I usually make molds of the masters and then cast them, I think this works fine.

      Delete
    2. His Gripenheim stuff is both the bee's knees and the cat's pajamas: http://thestonecuttersguild.tumblr.com/tagged/gripenhem

      Basically, his hobby is building early modern/fantasy towns in 28mm.

      Delete
  2. very nice balsa wood cut up into cube and broken with the gran can make for a nice brick wall effect too :) Also pressing stone into the face of foam or gs or apoxie sculpt can create nice textures. if you are short on rocks (i have plenty in my head) you can also crumple up tinfoil and press that into a surface to get a nice natural stone texture.

    ReplyDelete
    Replies
    1. more excellent ideas. I think I'll try the tinfoil idea.

      Delete
  3. Well great idea to perform with foamboards and more creative things. Foamboardsource having too many options, which one will be perfect for this stone texture?

    ReplyDelete
    Replies
    1. I used foam board sold in the school supply section of the local CVS Pharmacy. I think it was called poster board.

      Delete